Skip to main content Skip to docs navigation

STAAD.Pro Help

STAAD.Pro Help

STAAD.Pro Help Getting Started What's New?Tutorials Modeling Analysis Design Postprocessing and Reports Data Files and Interoperability General Engineering Theory Technical Reference of STAAD Commands TR.0 STAAD Commands and Input Instructions TR.1 Command Language Conventions TR.2 Problem Initiation and Model Title TR.3 Unit Specification TR.4 Input/Output Width Specification TR.5 Set Command Specification TR.6 Data Separator TR.7 Page Control Commands TR.8 Ignore Specifications TR.9 No Design Specification TR.10 Job Information Data TR.11 Joint Coordinates Specification TR.12 Member Incidences Specification TR.13 Plate and Solid Elements TR.14 Plate Element Mesh Generation TR.15 Redefinition of Joint and Member Numbers TR.16 Entities as Single Objects TR.17 Rotation of Structure Geometry TR.18 Inactive/Delete Specification TR.19 User Steel Table Specification TR.20 Member Property Specification TR.21 Element/Surface Property Specification TR.22 Member and Element Releases TR.23 Axial Member Specifications TR.24 Element Plane Stress and Ignore Inplane Rotation Specification TR.25 Offset Specifications TR.26 Specifying and Assigning Material Constants TR.27 Support Specifications TR.28 Rigid Diaphragm Modeling TR.29 Definition of Member Attributes TR.30 Miscellaneous Settings for Dynamic Analysis TR.31 Definition of Load Systems TR.32 Loading Specifications TR.33 Reference Load Cases - Application TR.34 Frequency Calculation TR.35 Load Combination Specification TR.36 Calculation of Problem Statistics TR.37 Analysis Specification TR.37.1 Linear Elastic Analysis TR.37.2 P-Delta Analysis Options TR.37.3 Nonlinear Cable Analysis TR.37.4 Buckling Analysis TR.37.5 Direct Analysis TR.37.6 Steady State and Harmonic Analysis TR.37.7 Pushover Analysis TR.37.7.1 Beginning of Pushover Data TR.37.7.2 Define Input TR.37.7.3 Define Loading Pattern TR.37.7.4 Define Solution Control TR.37.7.5 Define Hinge Property TR.37.7.6 Define Spectral Parameters TR.37.7.7 End Pushover Data TR.37.7.8 Pushover Loading Input TR.37.7.9 Validation of Commands other than Input Parameters TR.37.8 Geometric Nonlinear Analysis TR.37.9 Imperfection Analysis TR.37.10 Floor Spectrum Command TR.38 Change Specification TR.39 Load List Specification TR.40 Load Envelope TR.41 Section Specification TR.42 Print Specifications TR.43 Stress/Force Output Printing for Surface Entities TR.44 Printing Section Displacements for Members TR.45 Printing the Force Envelope TR.46 Post Analysis Printer Plot Specifications TR.47 Size Specification TR.48 Steel and Aluminum Design Specifications TR.49 Code Checking Specification TR.50 Group Specification TR.51 Steel and Aluminum Take Off Specification TR.52 Timber Design Specifications TR.53 Concrete Design Specifications TR.54 Footing Design Specifications TR.55 Shear Wall Design TR.56 End Run Specification Index of Commands Ribbon Control Reference Verification Examples Application Examples OpenSTAAD

STAAD.Pro Help
Technical Reference of STAAD Commands
TR.37 Analysis Specification
TR.37.7 Pushover Analysis

TR.37.7 Pushover Analysis

This section describes how to define a pushover analysis in STAAD.Pro.

Note: This requires a STAAD.Pro Advanced Analysis license.

TR.37.7.1 Beginning of Pushover Data
All Pushover analysis related data are to be entered after entering this command.
TR.37.7.2 Define Input
The following sections describe the input parameters used for a pushover definition.
TR.37.7.3 Define Loading Pattern
The pattern of the push load distribution on the nodes of the structure to be entered.
TR.37.7.4 Define Solution Control
One of the two following methods must be specified to define the limit of the pushover analysis.
TR.37.7.5 Define Hinge Property
If the automatic hinge calculation per FEMA 356 is not used, then the hinge properties must be defined and these hinges must be assigned to members.
TR.37.7.6 Define Spectral Parameters
The parameters of this section are used to construct the response spectrum according to FEMA 356:2000.
TR.37.7.7 End Pushover Data
All Pushover data are to be entered before this command.
TR.37.7.8 Pushover Loading Input
Only two types of loading are accepted in pushover analysis.
TR.37.7.9 Validation of Commands other than Input Parameters

Parent Topic: TR.37 Analysis Specification

Related Concepts

G.17.4 Pushover Analysis
M.Pushover Loads

Related Tasks

A. To specify a pushover analysis

Related reference

Perform Pushover Analysis tab