V. IS456 2000-Singly Reinforced Square Beam
Verify the designed results produced by the program with hand calculated design results for a square beam section as per IS456:2000.
Details
- Length of beam, L = 3,000 mm (clear span)
- Width of beam, B = 300 mm
- Depth of beam, D = 300 mm
- Clear cover = 30 mm
- Diameter of main reinforcement = 16 mm
- Diameter of stirrups = 8 mm
- Characteristic strength of concrete, fck = 20 N/mm2
- Yield strength of steel, fy = 415 N/mm2
Loads: total uniform force = 35 kN/m
Validation
Effective Depth, d = 300 – 30 – 8 – (16/2) = 254 mm
Design for Flexure
Limiting moment value, Mz,limit = 0.138×fck×B×d2 = 0.138 × 20 × 300 × 2542 × 106 = 53.42 kN·m
From the STAAD.Pro analysis, Mz = 40.46 kN·m < Mz,limit at the start of the member (x = 0).
So, the actual moment is less than limiting moment then the section will be design as singly reinforced section.
- Percentage of tension reinforcement ρt = 0.674
Reinforcement at Start of Member (x = 0): top bars
Provide 3 - 16 mm diameter bars. Actual Ast, top = 3×(π/4)×(16)2 = 603.2 mm2
From the STAAD.Pro analysis, Mz = 35.84 kN·m < Mz,limit at the end of the member (x = 3 m).
The actual moment is less than the limiting moment. Thus, the section is designed as a singly reinforced section.
- Percentage of tension reinforcement ρt = 0.585
Reinforcement at Start of Member (x = 3): top bars
Provide 3 - 16 mm diameter bars. Actual Ast, top = 3×(π/4)×(16)2 = 603.2 mm2
Shear Strength of Concrete
Provide percentage of tension steel, ρt = 0.792.
From Table 19 of IS 456:2000, for M20 grade concrete, shear stress: Tc = 0.57 N/mm2 .
Factored shear force as per linear structural analysis in STAAD.Pro, Fy = 80.29 kN.
The nominal shear stress, Tv = Fy / (B×d) = 80.29 / (300 × 254) = 1.054 N/mm2 .
The maximum shear stress from Table 20 of IS 456:2000 for M20 grade concrete, Tc,max = 2.8 N/mm2 .
Tc < Tv < Tc,max , so provide shear reinforcement.
Shear strength of the reinforcement: Vus = Fy - Tc × B × d = 80.29 - 0.57 × 300 × 254 × 103 = 36.85 kN.
Provide 2 legged 8 mm diameter bar. So, the area of shear reinforcement, Asv = π/4 × 82×2 = 100.5 mm2 .
Using the formula of IS 456:200, the spacing for vertical stirrups:- 0.75 × d = 0.75 × 256 = 191 mm
- 300 mm
- ( 0.87× fy × Asv ) / (0.4 × B) = 302.5 mm
- Sv = 250.2 mm
So, provide 2 legged 8 mm diameter bar stirrups at 190 mm center to center.
Results
Result Type | Reference | STAAD.Pro | Difference | Comments |
---|---|---|---|---|
Reqd. area of steel at start section (mm2) | 513.6 | 519.32 | negligible | |
Reqd. area of steel at end section (mm2) | 445.6 | 449.98 | negligible | |
Spacing of shear reinforcement (mm) | 190 | 185 | negligible |
STAAD.Pro Input
The file C:\Users\Public\Public Documents\STAAD.Pro 2024\Samples \Verification Models\10 Concrete Design\India\IS456 2000-Singly Reinforced Square Beam.STD is typically installed with the program.
STAAD SPACE
START JOB INFORMATION
ENGINEER DATE 25-Jul-18
END JOB INFORMATION
INPUT WIDTH 79
UNIT METER KN
JOINT COORDINATES
1 0 0 0; 2 0 3 0; 3 0 6 0; 4 0 9 0; 5 3 9 0; 6 6 9 0; 7 6 6 0; 8 6 3 0;
9 6 0 0; 10 3 6 0; 11 3 3 0; 12 3 0 0; 13 0 0 3; 14 0 3 3; 15 0 6 3; 16 0 9 3;
17 3 9 3; 18 6 9 3; 19 6 6 3; 20 6 3 3; 21 6 0 3; 22 3 6 3; 23 3 3 3; 24 3 0 3;
25 0 0 6; 26 0 3 6; 27 0 6 6; 28 0 9 6; 29 3 9 6; 30 6 9 6; 31 6 6 6; 32 6 3 6;
33 6 0 6; 34 3 6 6; 35 3 3 6; 36 3 0 6;
MEMBER INCIDENCES
1 1 2; 2 2 3; 3 3 4; 4 4 5; 5 5 6; 6 6 7; 7 7 8; 8 8 9; 9 3 10; 10 10 7;
11 2 11; 12 11 8; 13 5 10; 14 10 11; 17 11 12; 18 2 14; 19 3 15; 20 4 16;
21 5 17; 22 6 18; 23 7 19; 24 8 20; 25 10 22; 26 11 23; 27 13 14; 28 14 15;
29 15 16; 30 16 17; 31 17 18; 32 18 19; 33 19 20; 34 20 21; 35 15 22; 36 22 19;
37 14 23; 38 23 20; 39 17 22; 40 22 23; 41 23 24; 42 14 26; 43 15 27; 44 16 28;
45 17 29; 46 18 30; 47 19 31; 48 20 32; 49 22 34; 50 23 35; 51 25 26; 52 26 27;
53 27 28; 54 28 29; 55 29 30; 56 30 31; 57 31 32; 58 32 33; 59 27 34; 60 34 31;
61 26 35; 62 35 32; 63 29 34; 64 34 35; 65 35 36;
DEFINE MATERIAL START
ISOTROPIC CONCRETE
E 2.17185e+07
POISSON 0.17
DENSITY 23.5616
ALPHA 1e-05
DAMP 0.05
TYPE CONCRETE
STRENGTH FCU 27579
END DEFINE MATERIAL
MEMBER PROPERTY AMERICAN
4 5 9 TO 12 18 TO 26 30 31 35 TO 38 42 TO 50 54 55 59 TO 62 PRIS YD 0.3 ZD 0.3
1 TO 3 6 TO 8 13 14 17 27 TO 29 32 TO 34 39 TO 41 51 TO 53 56 TO 58 -
63 TO 65 PRIS YD 0.4 ZD 0.4
CONSTANTS
MATERIAL CONCRETE ALL
SUPPORTS
1 9 12 13 21 24 25 33 36 FIXED
MEMBER RELEASE
59 START MX
59 END MX
LOAD 1 LOADTYPE Dead TITLE DL
MEMBER LOAD
4 5 9 TO 12 18 TO 26 30 31 35 TO 38 42 TO 50 54 55 59 TO 62 UNI GY -3.125
4 5 9 TO 12 18 TO 26 30 31 35 TO 38 42 TO 50 54 55 59 TO 62 UNI GY -1.875
LOAD 2 LOADTYPE Live TITLE LL
MEMBER LOAD
4 5 20 22 44 46 54 55 UNI GY -7.875
21 30 31 45 UNI GY -15.75
9 TO 12 18 19 23 24 42 43 47 48 59 TO 62 UNI GY -30
25 26 35 TO 38 49 50 UNI GY -90
LOAD COMB 3 GENERATED IS:456/IS:800 GENRAL_STRUCTURES 1
1 1.5 2 1.5
LOAD COMB 4 GENERATED IS:456/IS:800 GENRAL_STRUCTURES 2
1 1.2 2 1.2
LOAD COMB 5 GENERATED IS:456/IS:800 GENRAL_STRUCTURES 3
1 1.5
LOAD COMB 6 GENERATED IS:456/IS:800 GENRAL_STRUCTURES 4
1 0.9
LOAD COMB 7 COMBINATION LOAD CASE 7
1 1.0 2 1.0
PERFORM ANALYSIS PRINT ALL
PRINT SUPPORT REACTION
PRINT MEMBER FORCES
LOAD LIST 3 TO 6
START CONCRETE DESIGN
CODE INDIAN
CLB 0.03 ALL
CLT 0.03 ALL
FC 20000 MEMB 59
FYMAIN 415000 MEMB 59
FYSEC 415000 MEMB 59
MAXMAIN 16 MEMB 59
MAXSEC 8 MEMB 59
MINMAIN 16 MEMB 59
MINSEC 8 MEMB 59
TRACK 2 MEMB 59
DESIGN BEAM 59
END CONCRETE DESIGN
FINISH
STAAD.Pro Output
====================================================
IS 456 - 2000 B E A M D E S I G N R E S U L T S
====================================================
============================================================================
IS-456 L I M I T S T A T E D E S I G N
B E A M N O. 59 D E S I G N R E S U L T S
M20 Fe415 (Main) Fe415 (Sec.)
LENGTH: 3000.0 mm SIZE: 300.0 mm X 300.0 mm COVER: 40.0 mm
DESIGN LOAD SUMMARY (KN MET)
----------------------------------------------------------------------------------
SECTION |FLEXURE (Maxm. Sagg./Hogg./Eqv. moments) | SHEAR
(in mm) | P MZ MX ME Load # | VY MX VE Load #
----------------------------------------------------------------------------------
0.0 | 0.00 0.00 0.00 0.00 3 | 80.29 0.00 80.29 3
| 0.00 -40.46 0.00 -40.46 3 |
250.0 | 0.00 0.00 0.00 0.00 3 | 67.16 0.00 67.16 3
| 0.00 -22.03 0.00 -22.03 3 |
500.0 | 0.00 0.00 0.00 0.00 3 | 54.04 0.00 54.04 3
| 0.00 -6.88 0.00 -6.88 3 |
750.0 | 0.00 4.99 0.00 4.99 3 | 40.91 0.00 40.91 3
| 0.00 0.00 0.00 0.00 3 |
1000.0 | 0.00 13.58 0.00 13.58 3 | 27.79 0.00 27.79 3
| 0.00 0.00 0.00 0.00 3 |
1250.0 | 0.00 18.89 0.00 18.89 3 | 14.66 0.00 14.66 3
| 0.00 0.00 0.00 0.00 3 |
1500.0 | 0.00 20.91 0.00 20.91 3 | 1.54 0.00 1.54 3
| 0.00 0.00 0.00 0.00 3 |
1750.0 | 0.00 19.66 0.00 19.66 3 | -11.59 0.00 11.59 3
| 0.00 0.00 0.00 0.00 3 |
2000.0 | 0.00 15.12 0.00 15.12 3 | -24.71 0.00 24.71 3
| 0.00 0.00 0.00 0.00 3 |
2250.0 | 0.00 7.30 0.00 7.30 3 | -37.84 0.00 37.84 3
| 0.00 0.00 0.00 0.00 3 |
2500.0 | 0.00 0.00 0.00 0.00 3 | -50.96 0.00 50.96 3
| 0.00 -3.80 0.00 -3.80 3 |
2750.0 | 0.00 0.00 0.00 0.00 3 | -64.09 0.00 64.09 3
| 0.00 -18.18 0.00 -18.18 3 |
3000.0 | 0.00 0.00 0.00 0.00 3 | -77.21 -0.00 77.21 3
| 0.00 -35.84 -0.00 -35.84 3 |
----------------------------------------------------------------------------
STAAD SPACE -- PAGE NO. 35
SUMMARY OF REINF. AREA (Sq.mm)
----------------------------------------------------------------------------
SECTION | TOP | BOTTOM | STIRRUPS
(in mm) | Reqd./Provided reinf. | Reqd./Provided reinf. | (2 legged)
----------------------------------------------------------------------------
0.0 | 519.32/ 603.19( 3-16d )| 0.00/ 402.12( 2-16d )| 8d @ 185 mm
250.0 | 261.02/ 603.19( 3-16d )| 0.00/ 402.12( 2-16d )| 8d @ 185 mm
500.0 | 184.34/ 603.19( 3-16d )| 0.00/ 402.12( 2-16d )| 8d @ 185 mm
750.0 | 0.00/ 402.12( 2-16d )| 154.84/ 603.19( 3-16d )| 8d @ 185 mm
1000.0 | 0.00/ 402.12( 2-16d )| 156.06/ 603.19( 3-16d )| 8d @ 185 mm
1250.0 | 0.00/ 402.12( 2-16d )| 221.19/ 603.19( 3-16d )| 8d @ 185 mm
1500.0 | 0.00/ 402.12( 2-16d )| 246.77/ 603.19( 3-16d )| 8d @ 185 mm
1750.0 | 0.00/ 402.12( 2-16d )| 230.86/ 603.19( 3-16d )| 8d @ 185 mm
2000.0 | 0.00/ 402.12( 2-16d )| 174.69/ 603.19( 3-16d )| 8d @ 185 mm
2250.0 | 0.00/ 402.12( 2-16d )| 154.84/ 603.19( 3-16d )| 8d @ 185 mm
2500.0 | 184.34/ 603.19( 3-16d )| 0.00/ 402.12( 2-16d )| 8d @ 185 mm
2750.0 | 212.33/ 603.19( 3-16d )| 0.00/ 402.12( 2-16d )| 8d @ 185 mm
3000.0 | 449.98/ 603.19( 3-16d )| 0.00/ 402.12( 2-16d )| 8d @ 185 mm
----------------------------------------------------------------------------
SHEAR DESIGN RESULTS AT DISTANCE d (EFFECTIVE DEPTH) FROM FACE OF THE SUPPORT
-----------------------------------------------------------------------------
SHEAR DESIGN RESULTS AT 452.0 mm AWAY FROM START SUPPORT
VY = 56.56 MX = 0.00 LD= 3
Provide 2 Legged 8d @ 185 mm c/c
SHEAR DESIGN RESULTS AT 452.0 mm AWAY FROM END SUPPORT
VY = -53.48 MX = 0.00 LD= 3
Provide 2 Legged 8d @ 185 mm c/c
============================================================================
********************END OF BEAM DESIGN RESULTS********************