V. ASCE 7 Torsion Irregularity
Verify the torsional irregularity check per the ASCE 7-16 specifications.
Details
A three story building is modelled with floor diaphragms defined at each floor level.
A 1 kip (4.4482 kN) load is applied to each diaphragm in both the global X and Z directions. In STAAD.Pro, this is modelled using an analytical node in each diaphragm. This is used to obtain the displacements in the nodes of the diaphragm.
Validation
The displacements induced because of the applied loads on the control nodes for the nodes situated on the extremities of each diaphragm is taken from the STAAD.Pro output for each lateral direction.
Diaphragm | Control Node | Primary LC Number | Diaphragm Extremities | Displacements (mm) | ∆max/∆min | Status | ||
---|---|---|---|---|---|---|---|---|
Extreme Node 1 | Extreme Node 2 | ∆x Extreme Node 1 | ∆x Extreme Node 2 | |||||
1 | 17 | 1 | 2 or 3 | 6 or 7 | 0.0482 × 10 = 0.482 | 0.0482 × 10 = 0.482 | 0.482/0.482 = 1 | OK |
2 | 18 | 2 | 9 or 10 | 11 or 12 | 0.2443 × 10 = 2.443 | 0.2443 × 10 = 2.443 | 2.443/2.443 = 1 | OK |
3 | 19 | 3 | 13 or 14 | 15 or 16 | 0.6090 × 10 = 6.090 | 0.6090 × 10 = 6.090 | 6.090/6.090 = 1 | OK |
Diaphragm | Control Node | Primary LC Number | Diaphragm Extremities | Displacements (mm) | ∆max/∆min | Status | ||
---|---|---|---|---|---|---|---|---|
Extreme Node 1 | Extreme Node 2 | ∆z Extreme Node 1 | ∆z Extreme Node 2 | |||||
1 | 17 | 4 | 2 or 6 | 3 or 7 | 0.0234 × 10 = 0.234 | 0.0361 × 10 = 0.361 | 0.361/0.234 = 1.543 | FAIL |
2 | 18 | 5 | 9 or 11 | 10 or 12 | 0.0919 × 10 = 0.919 | 0.1243 × 10 = 1.243 | 1.243/0.919 = 1.353 | OK |
3 | 19 | 6 | 13 or 15 | 14 or 16 | 0.1884 × 10 = 1.884 | 0.2441 × 10 = 2.441 | 2.441/1.884 = 1.296 | OK |
Results
Result Type | Reference | STAAD.Pro | Difference | Comments | |
---|---|---|---|---|---|
X Direction | 1 | OK | OK | none | |
2 | OK | OK | none | ||
3 | OK | OK | none | ||
Z Direction | 1 | Fail | Fail | none | |
2 | OK | OK | none | ||
3 | OK | OK | none |
STAAD.Pro Input File
The file C:\Users\Public\Public Documents\STAAD.Pro 2024\Samples \Verification Models\06 Loading\IBC\IBC 2018 Torsion Irregularity.STD is typically installed with the program.
STAAD SPACE
START JOB INFORMATION
ENGINEER DATE 05-Mar-19
END JOB INFORMATION
INPUT WIDTH 79
UNIT METER KN
JOINT COORDINATES
1 0 0 0; 2 0 5 0; 3 5 5 0; 4 5 0 0; 5 0 0 5; 6 0 5 5; 7 5 5 5; 8 5 0 5;
9 0 10 0; 10 5 10 0; 11 0 10 5; 12 5 10 5; 13 0 15 0; 14 5 15 0; 15 0 15 5;
16 5 15 5; 17 1.239 5 2.5; 18 1.239 10 2.5; 19 1.313 15 2.5
MEMBER INCIDENCES
1 1 2; 2 2 3; 3 3 4; 4 2 6; 5 3 7; 6 5 6; 7 6 7; 8 7 8; 9 2 9; 10 3 10;
11 6 11; 12 7 12; 13 9 10; 14 9 11; 15 10 12; 16 11 12; 17 9 13; 18 10 14;
19 11 15; 20 12 16; 21 13 14; 22 13 15; 23 14 16; 24 15 16;
DEFINE MATERIAL START
ISOTROPIC CONCRETE
E 2.17185e+07
POISSON 0.17
DENSITY 23.5616
ALPHA 1e-05
DAMP 0.05
TYPE CONCRETE
STRENGTH FCU 27579
END DEFINE MATERIAL
MEMBER PROPERTY AMERICAN
2 3 5 7 8 10 12 13 15 16 18 20 21 23 24 PRIS YD 0.35 ZD 0.25
MEMBER PROPERTY AMERICAN
1 4 6 9 11 14 17 19 22 PRIS YD 0.5 ZD 0.65
CONSTANTS
MATERIAL CONCRETE ALL
SUPPORTS
1 4 5 8 FIXED
MEMBER CRACKED
1 3 6 8 TO 12 17 TO 20 REDUCTION RIY 0.7 RIZ 0.7
2 4 5 7 13 TO 16 21 TO 24 REDUCTION RIY 0.35 RIZ 0.35
DEFINE REFERENCE LOADS
LOAD R1 LOADTYPE Mass TITLE REF LOAD CASE 1
SELFWEIGHT X 1
SELFWEIGHT Y 1
SELFWEIGHT Z 1
END DEFINE REFERENCE LOADS
FLOOR DIAPHRAGM
DIA 1 TYPE RIG HEI 5
DIA 2 TYPE RIG HEI 10
DIA 3 TYPE RIG HEI 15
*CHECK IRREGULARITIES CODE IS1893 2016
CHECK IRREGULARITIES CODE ASCE7
DEFINE IBC 2018
ZIP 92887 I 1 RX 3 RZ 4 SCLASS 1 TL 8
LOAD 1 LOADTYPE None TITLE Diaphragm 1 Unit Load FX
JOINT LOAD
17 FX 4.4482
LOAD 2 LOADTYPE None TITLE Diaphragm 2 Unit Load FX
JOINT LOAD
18 FX 4.4482
LOAD 3 LOADTYPE None TITLE Diaphragm 3 Unit Load FX
JOINT LOAD
19 FX 4.4482
LOAD 4 LOADTYPE None TITLE Diaphragm 1 Unit Load FZ
JOINT LOAD
17 FZ 4.4482
LOAD 5 LOADTYPE None TITLE Diaphragm 2 Unit Load FZ
JOINT LOAD
18 FZ 4.4482
LOAD 6 LOADTYPE None TITLE Diaphragm 3 Unit Load FZ
JOINT LOAD
19 FZ 4.4482
PERFORM ANALYSIS
PRINT ANALYSIS RESULTS
PRINT DIA CR
FINISH
STAAD.Pro Output
STAAD.PRO IRREGULARITIES CHECK - ( ASCE7-2016 ) v1.0
*********************************************************
--TORSION IRREGULARITY CHECKS
Torsion Irregularity Check
Ref: Fig. C12.3-1 T1- Ratio Limit(s): 1.20, 1.40
------------------------------------------------
Dia. Extreme Points of Dia in X Extreme Points of Dia in Z
Node Disp. Node Disp. Node Disp. Node Disp.
(mm) (mm) (mm) (mm)
------------------------------------------------------------------------
1 7 0.48231 2 0.48231 3 0.36107 2 0.23351
2 12 2.44302 9 2.44302 10 1.24284 9 0.91874
3 16 6.08970 13 6.08970 14 2.44124 13 1.88424
Diaphragm D X-max/avg D Z-max/avg Status
--------------------------------------
1 1.0000 1.2145 FAIL
2 1.0000 1.1499 OK
3 1.0000 1.1288 OK
--GEOMETRY IRREGULARITY CHECKS
Re-Entrant Corner Check.
(Ref: Fig. C12.3-1 T2- Ratio Limit: 0.15 )
------------------------------------------
***NOTE: No Irregular Re-Entrant Nodes found in the diaphragm.
***NOTE: No Irregular Re-Entrant Nodes found in the diaphragm.
***NOTE: No Irregular Re-Entrant Nodes found in the diaphragm.
--MASS IRREGULARITY CHECKS
Mass Irregularity Check
Ref: Fig. C12.3-2 T2- Ratio Limit: 1.50
---------------------------------------
Dia. Level Mass Above Below Ratio Ratio Status
( m) ( kN) ( kN) ( kN) Above Below
---------------------------------------------------------------------
1 5.000 166.404 166.404 Base 1.000 N/A OK
2 10.000 166.404 117.808 166.404 1.412 1.000 OK
3 15.000 117.808 Top 166.404 N/A 0.708 OK