D5.A.5.4.2 Detailed stress check
This method is used when the TORSION parameter is specified as two (2).
This method performs a detailed torsional analysis of a member depending on the torsion loading conditions and the support conditions at the member ends. This method is based on the SCI publication P057 and includes any warping stresses (direct warping stresses and warping shear stresses) depending on the end conditions of the member. This implementation considers seven different cases of loading and end conditions as given in publication P057 – Section 6. The loading/end conditions for a member are specified by the use of the CMT design parameter (Refer to D5.A.6 Design Parameters for parameter values and descriptions).
All the equations used to evaluate the torsional moments and associated stresses are as given in Appendix B of P057. The resultant stresses are evaluated at various sections along the length of the member and the following checks will be performed:
Clause 6.2.7(1) – Torsional resistance of the section.
In general, the torsion at any section TEd is resolved into two components, viz.
The pure torsional (St. Venant’s) moment (Tt,Ed) and
The warping torsional moment(Tw,Ed)
Therefore,
TEd = Tt,Ed + Tw,Ed = GJφ’ = EHφ’’’ | [Ref SCI pub. P057] |
= |
The torsional resistance of the section is also considered as the sum of the pure torsion resistance and the warping torsion resistance. The pure torsion resistance (Tt,Rd) and the warping torsional resistance (Tw,Rd) are evaluated as:
For closed sections:
Tt,Rd = 2 · Ac · t · τmax
where= | ||
= | ||
= |
For open sections (I & channel):
Tt,Rd = τmax · J / t
where= | ||
= |
Tw,Rd = (fy/ Γm0)· t · b2 / 6
where= | ||
= |
The check according to Cl 6.2.7(1) will then be performed to ensure that the following conditions are satisfied:
Tt,Ed / Tt,Rd ≤ 1
Tw,Ed / Tw,Rd ≤ 1
TEd / TRd ≤ 1
Clause 6.2.7(9) – Plastic shear resistance due to torsion
STAAD.Pro checks for shear resistance of a section based on Cl. 6.2.6 for EC3 and the plastic shear resistance (in the absence of torsion) is evaluated as:
where= |
When torsion is present, along with the shear force, the design shear resistance will be reduced to Vpl,T,Rd, where Vpl,T,Rd is evaluated as follows:
-
For I or H Sections:
-
For Channel Sections:
-
For Structural Hollow Sections:
= | ||
= |
The various shear stresses due to torsion τt,Ed and τw,Ed are evaluated as follows:
-
For Closed sections:
The shear stresses due to warping can be ignored as they will be insignificant and hence:
whereτt,Ed = TEd/(2·Ac·t) [Ref NCCI Sn007b-EN-EU] - TEd
= - the applied torsion
- Ac
= - the area delimited by the mean perimeter
- t
= - the thickness of the cross section
- τw,Ed
= - 0, since warping is ignored
-
For Open sections [I, H, Channel] sections:
For I and H sections, the web will not be subject to warping stresses and therefore warping shear can be ignored (τw,Ed=0).
The stress due to pure torsion is evaluated as:
whereτt,Ed = G·t·φ’ [Ref SCI pub. P057] - G
= - the shear modulus
- φ’
= - a function depending on the end condition and loading(T). This will be taken from section 6 and Annex B of P057.
Note: Although the maximum stress is at the thickest section of the profile, the program uses the web thickness for this clause (since the shear capacity is based on the web area) unless the load is parallel to the flanges, in which case the flange thickness is used.For channel sections that are free to warp at the supports and, thus, are not subject to warping stresses:
The warping shear stress is evaluated as:
whereτw,Ed = E·Sw·φ’’’ / t [Ref SCI pub. P057] - E
= - the elastic modulus
- Sw
= - the warping statistical moment
- φ’
= - a function depending on the end condition and loading(T). This will be taken from section 6 and Annex B of P057.
Clause 6.2.7(5) – Check for elastic verification of yield
Eurocode 3 gives yield criterion as per eqn. 6.1 and STAAD.Pro uses the yield criterion given in EC-3. When a member is subject to combined bending and torsion, some degree of interaction occurs between the two effects. The angle of twist caused by torsion is amplified by the bending moments and will induce additional warping moments and torsional shears. Account must also be taken of the additional minor axis moments produced by the major axis moments acting through the torsional deformations, including the amplifications mentioned earlier.
For members subject to bending and torsion, the stresses are evaluated as follows:
- Direct bending stress (major axis): σbz = Mz / Zz
- Direct bending stress (minor axis): σby = My / Zy
- Direct stress due to warping: σw = E·Wns· φ’’
- Direct stress due to twist (min. axis): σbyt = Myt / Zy
- Direct stress due to axial load (if any): σc = P/ A
= | ||
= | ||
= | ||
= |
Shear stresses due to torsion and/or warping is evaluated as described above for Clause 6.2.7(9).
Check for yield (capacity checks) is then done according to Eqn 6.1 of EN 1993-1-1:2005, as described for the Basic Stress Check (TORSION = 1):
Clause EC-3:6 App A – Check for combined Torsion and Lateral Torsional buckling
The interaction check due to the combined effects of bending (including lateral torsional buckling) and torsion will be checked using Annex A of EN 1993-6: 2007. Note that this interaction equation does not include the effects of any axial load.
Members subject to combined bending and torsion will be checked to satisfy:
where= | ||
= | ||
= | ||
= | ||
= | ||
= | ||
= | ||
= | ||
= | ||
= |