TR.31.2.16 IBC 2015 Seismic Load Definition

The specifications of the seismic loading chapters of the International Code Council 2015 code and the ASCE 7-10 code for seismic analysis of a building using a static equivalent approach have been implemented as described in this section. Depending on the definition, equivalent lateral loads will be generated in the horizontal direction(s).

General Format

There are two stages of command specification for generating lateral loads. This is the first stage and is activated through the DEFINE IBC 2015 LOAD command.

DEFINE IBC 2015 (ACCIDENTAL) LOAD

map-spec  ibc15-spec

weight-data

Refer to Common Weight Data for information on how to specify structure weight for seismic loads.

Where:

map-spec  = { ZIP f₁ | LAT f₂ LONG f₃ | SS f₄ S1 f₅ }

Where:

Parameter	Description
ZIP f1	The zip code of the site location to determine the latitude and longitude and consequently the Ss and S1 factors. (ASCE 7-10 Chapter 22).
LAT f2	The latitude and longitude, respectively, of the site used with the longitude to determine the Ss and S1 factors. (ASCE 7-10 Chapter 22).
LONG f3	The latitude and longitude, respectively, of the site used with the longitude to determine the Ss and S1 factors. (ASCE 7-10 Chapter 22).
SS f4	The mapped MCE for 0.2s spectral response acceleration. (IBC 2015 Clause 1613.5.1, ASCE 7-10 Clause 11.4.1).
S1 f5	The mapped MCE spectral response acceleration at a period of 1 second as determined in accordance with Section 11.4.1 ASCE7-10.

ibc15-spec  = { RX f6 RZ f7 I f8 TL f9 SCLASS f10 (CTX f11) (CTZ f12) (PX f13) (PZ f14) (XX f15) (XZ f16) (FA f17) (FV f18) }

Where:

Parameter	Description
RX f6	The response modification factor, R, for lateral load along the X direction, (ASCE 7-10 Table 12.2.1). This is the value used for calculating C_s.
RZ f7	The response modification factor, R, for lateral load along the Z direction, (ASCE 7-10 Table 12.2.1) This is the value used for calculating C_s.
I f8	Occupancy importance factor (IBC 2015 Clause 1604.5, ASCE 7-10 Table 11.5-1).
TL f9	Long-Period transition period in seconds (ASCE 7-10 Clause 11.4.5 and Chapter 22).
SCLASS f10	Site class. Enter 1 through 6 in place of A through F, see table below (IBC 2015 clause 1613.3.2, ASCE 7-10 Section 20.3)
CTX f11	Optional CT value in X-direction to calculate time period. (ASCE 7-10 Table 12.8-2). If specified, it is your responsibility to provide the value in the correct system of units. Refer to AISC 7-10 for values. If the value of C_t is not provided, then the program computes the average value of the modulus of elasticity of the model, $E_{a v g} = \sum E / M$ (where M is the number of members) and uses this to determine the structure type: E_avg < 4,000 ksi, the program uses a C_t for a moment-resisting concrete frame. E_avg > 10,000 ksi, the program uses a C_t for a moment-resisting steel frame. 4,000 ksi ≤ E_avg ≤ 10,000 ksi, the program uses a C_t value for "all other structural systems". Note: It is your responsibility to ensure that the structure type used actually matches the description for the automatically determined structure when C_t not specified. Refer to the IBC/ASCE 7 code for detailed descriptions. ASCE 7-10 also includes "Eccentrically braced steel frames". STAAD.Pro does not select this value automatically. For this structure type, you must specify C_t.
CTZ f12	Optional CT value in Z-direction to calculate time period. (ASCE 7-10 Table 12.8-2). Refer to `CTX` for details.
PX f13	Optional period of structure (in sec) in X-direction to be used as fundamental period of the structure. If not entered the value is calculated from the code. (ASCE 7-10 Table 12.8-2).
PZ f14	Optional period of structure (in sec) in Z-direction to be used as fundamental period of the structure. If not entered the value is calculated from the code. (ASCE 7-10 Table 12.8-2).
XX f15	Optional exponent value, x, in X-direction, used in equation 12.8-7, ASCE 7. (ASCE 7-10 table 12.8-2). If the value of x is not provided, then the program computes the average value of the modulus of elasticity of the model to determine the structure type. Refer to `CTX` for details.
XZ f16	Optional exponent value, x, in Z-direction, used in equation 12.8-7, ASCE 7. (ASCE 7-10 table 12.8-2). If the value of x is not provided, then the program computes the average value of the modulus of elasticity of the model to determine the structure type. Refer to `CTX` for details.
FA f17	Optional Short-Period site coefficient at 0.2s. Value must be provided if `SCLASS` set to F (i.e., 6). (IBC 2015 Clause 1613.3.3, ASCE 7-10 Section 11.4.3).
FV f18	Optional Long-Period site coefficient at 1.0s. Value must be provided if `SCLASS` set to F (i.e., 6). (IBC 2015 Clause 1613.3.3, ASCE 7-10 Section 11.4.3).

Note: For additional details on the application of a seismic load definition used to generate loads, refer to TR.32.12.2 Generation of Seismic Loads.

Implementation and Methodology

Refer to TR.31.2.15 IBC 2012 Seismic Load Definition for details on the implementation of the IBC 2015 / IBC 2012 / ASCE 7-10 static seismic method.

Example 1

DEFINE IBC 2015
LAT 38.0165 LONG -122.105 I 1.25 RX 2.5 RZ 2.5 SCLASS 4 -
TL 12 FA 1 FV 1.5
SELFWEIGHT
JOINT WEIGHT 
51 56 93 100 WEIGHT 650
MEMBER WEIGHT
151 TO 156 158 159 222 TO 225 324 TO 331 UNI 45

Example 2

The following example shows the commands required to enable the program to generate the lateral loads. Refer to TR.32.12 Generation of Loads for this information.

LOAD 1 (SEISMIC LOAD IN X DIRECTION)
IBC LOAD X 0.75
LOAD 2 (SEISMIC LOAD IN Z DIRECTION)
IBC LOAD Z 0.75