TR.32.10.1.15 Response Spectrum Specification per SP 14.13330.2011
This command may be used to specify and apply the RESPONSE SPECTRUM loading as per SP 14.13330.2011 for dynamic analysis.
General Format
SPECTRUM { SRSS  CQC } SP11 (ECCENTRICITY) A f_{1} *{ {X f_{2}  Y f_{3}  Z f_{4}} ACCELERATION (SCALE f_{5}) (DAMP f_{6} ) (LOG) (MIS f_{7}) (ZPA f_{8}) ({ DOMINANT f_{9}  SIGN }) SOIL { 1  2  3}
The data from SPECTRUM through SCALE above must be on the first line of the command, the remaining data can be on the first or subsequent lines with all but last ending with a hyphen (limit of four lines per spectrum).
Where:
Parameter  Default Value  Description 

A f1  Zoning factor, A, which is based on maximum acceleration factor for the seismic zone. This factor must be modified for SOIL types other than 2.  
X f2 Y f3 Z f5 
0.0  Factors for the input spectrum to be applied in X, Y, & Z directions. Any one or all directions can be input. Directions not provided will default to zero. 
SCALE f5  A linear scaling factor by which the spectrum data will be multiplied according to the provisions of SP 14.13330.2011.  
DAMP f6  0.05 
The damping ratio.
Specify a value of exactly 0.0000011 to ignore damping.

MISSING f7  Optional parameter to use the "Missing Mass" method to include the static
effect of the masses not represented in the modes. The spectral acceleration
length/sec^{2} for this missing mass mode is the f7 value entered in
length per second squared units (this value is not multiplied by
SCALE). If f7 is zero, then the spectral
acceleration at the
ZPA f8 frequency is used. If f8 is zero or not
entered, then the spectral acceleration at 33Hz is used. The results of this
calculation are SRSSed with the modal combination results.
For SRSS and CQC, the results of this calculation are SRSSed with the modal combination results. If either of f7 or f8 are not entered, the defaults will be used. Missing mass does not include the effect of masses lumped at the supports unless the support is a stiff spring or an Enforced support. 

ZPA f8  33.0 Hz  The zero period acceleration value for use with MISSING option only. Defaults to 33 Hz if not entered. The value is printed but not used if MISSING f7 is entered. 
DOMINANT f9  1  The dominant mode method. All results will have the same sign as mode number f9 alone would have if it were excited then the scaled results were used as a static displacements result. Defaults to mode 1 if no value entered. If a 0 value entered, then the mode with the greatest % participation in the excitation direction will be used (only one direction factor may be nonzero). 
combmethod = { SRSS  CQC } are methods of combining the responses from each mode into a total response.
The CQC method requires damping. The SRSS method does not use damping unless spectraperiod curves are made a function of damping (see File option below). CQC includes the effect of response magnification due to closely spaced modal frequencies. CQC is a more sophisticated and realistic methods and is recommended.
The specifier SP11 is mandatory to denote that the applied loading is as per the guidelines of SP 14.13330.2011.
 ECCENTRICITY
 automatic introduction of artificial mass eccentricity according to SP 14.13330.2011.
 ACCELERATOIN
 indicates that the Acceleration spectra will be entered.
 DAMP, MDAMP, and CDAMP
 select source of damping input:
 DAMP indicates to use the f2 value for all modes
 MDAMP indicates to use the damping entered or computed with the DEFINE DAMP command if entered, otherwise default value of 0.05 will be used
 CDAMP indicates to use the composite damping of the structure calculated for each mode. You must specify damping for different materials under the CONSTANT specification
 LINEAR or LOGARITHMIC
 Select Linear or Logarithmic interpolation of the
input Spectra versus Period curves for determining the spectra value for a mode
given its period. Linear is the default. Since Spectra versus Period curves are often
linear only on LogLog scales, the logarithmic interpolation is recommended in
such cases; especially if only a few points are entered in the spectra curve.
When FILE filename is entered, the interpolation along the damping axis will be linear.
 SIGN
 This option results in the creation of signed values for all results. The sum of squares of positive values from the modes are compared to sum of squares of negative values from the modes. If the negative values are larger, the result is given a negative sign. This command is ignored for ABS option.
 SOIL
 Defines the subsoil conditions on which the response spectrum will be generated.
Description
Results of frequency and mode shape calculations may vary significantly depending upon the mass modeling. All masses that are capable of moving should be modeled as loads, applied in all possible directions of movement. For more information on dynamic mass modeling, refer to sections TR.32 Loading Specifications and G.17.3 Dynamic Analysis
Example
STAAD PLANE RESPONSE SPECTRUM ANALYSIS
START JOB INFORMATION
JOB NAME Plane Russian example
ENGINEER DATE 12Feb08
END JOB INFORMATION
UNIT METER KN
JOINT COORDINATES
1 0 0 0; 2 7.2 0 0; 3 0 4.5 0; 4 7.2 4.5 0; 5 0 9.0 0; 6 7.2 9.0 0;
MEMBER INCIDENCES
1 1 3; 2 2 4; 3 3 5; 4 4 6; 5 3 4; 6 5 6;
MEMBER PROPERTY RUSSIAN
1 TO 4 PRIS AY 10000 YD 0.6 ZD 0.6
5 TO 6 PRIS YD 0.9 ZD 0.3
SUPPORTS
1 TO 2 FIXED BUT MZ
3 TO 6 FIXED BUT FX
CONSTANTS
E 30.0e+006 ALL
POISSON 0.2 ALL
CUT OFF MODE SHAPE 1
*NEXT LOAD WILL BE RESPONSE SPECTRUM LOAD
*WITH MASSES PROVIDED IN TERMS OF LOAD.
LOAD 1 SEISMIC LOADING
JOINT LOAD
3 4 FX 310.586
3 4 FY 310.586
5 6 FX 310.586
5 6 FY 310.586
SPECTRUM CQC SP11 ECC A 1.0 X 1.0 ACC MIS SOIL 2
PERFORM ANALYSIS
PRINT MODE SHAPES
PRINT STORY DRIFT
PRINT ANALYSIS RESULTS
FINISH