Angle
|
Positive <angle value>
|
Branch 1 | Height
|
Positive <numeric value>
- Sets distance
between main branch center line to the end of saddle. Automatically set by
application.
|
Branch Length
|
Positive <numeric value>
- Sets side branch
center line length up to connect point. The application
limits values to prevent illogical geometry.
|
Branch Offset
|
<numeric value>
- Sets side branch
lateral distance from End1.
|
Branch 2 | Radius
(for Drop Cheek fittings )
|
<numeric value> greater than or equal to
zero.
- Sets the inside
radius between End1 and End2.
|
Branch 3 | Radius
(for Drop Cheek fittings)
|
<numeric value> greater than or equal to
zero.
- Sets the inside
radius between End1 and End3.
|
Branch 2 | Depth
Offset
(for Drop Cheek fittings)
|
<numeric value>
- Sets center line
distance between End1 connect point and the divergence point of side branch
leading to End2.
|
Branch 3 | Depth
Offset
(for Drop Cheek fittings)
|
<numeric value>
- Sets center line
distance between End1 connect point and the divergence point of side branch
leading to End3.
|
Center To Top Distance
|
Positive <numeric value>
- Sets distance
between main branch center line to the saddle connect point.
|
Cone Angle
|
<angle value>
- Sets the side
branch angle of taper as it blends into the main branch.The application
limits values to prevent illogical geometry.
|
Connection 1 | Length (L1)
|
Positive <numeric value>
- Sets straight
length at End Spec1 for rectangular shapes.
- Sets straight
length between End1 and End2 connections for round and oval shapes.
|
Connection 2 | Length (L2)
Connection | Length
|
Positive <numeric value>
- Sets straight
length at End2 for rectangular shapes.
- Sets connection
lengths for round and oval shapes.
- Sets connection
lengths for saddle main tube (End1 and End2).
|
Connection 3 | Length (L3)
|
Positive <numeric value>
- Sets straight
length at End3 for rectangular shapes.
- Sets connection
length on saddle (End3).
|
Connection 4 | Length (L4)
|
Positive <numeric value>
- Sets inset
distance on the right side of saddle.
|
Connection 5 | Length (L5)
Length 5 (L5)
|
Positive <numeric value>
- Sets the distance
from the main branches' (End1 and End2) center line to the side branch's (End3)
connect point.
|
Connection | End Type
|
fl
-<numeric value>
- Sets and sizes
end with a flange connection.
m
-<numeric value>
- Sets and sizes
end with a male connection.
fe
-<numeric value>
- Sets and sizes
end with a female connection.
Separate End Type entries for each End Spec with a semi
colon.
Example: fl-2;fe-.13 creates a flange at End1 with
size 2, and a female connection at End2 with an overall reduction of
component's dimensions of .13
|
Inset
|
Positive <numeric value>
- Sets offset
distance between End1 connect point and intersection with the saddle branch.
|
Inlet to Branch Offset
|
<numeric value>
- Sets the center
line distance between End1 connect point and side branch (End3) start point.
The application adjusts L property when
X11 is large, and restricts small values for X11 to ensure logical fitting.
|
Radius
|
Positive <numeric value>
- Sets side branch
inner radius.
|
Radius 1 (R1)
|
<numeric value> greater than or equal to
zero.
- Sets radius
between End1 and End3.
|
Radius 2 (R2)
|
<numeric value> greater than or equal to
zero.
- Sets radius
between End2 and End3.
|
Reducer Length
|
<numeric value>
- Automatically set
by the application.
|
Rise
|
<numeric value>
- Sets saddle
(End3) offset distance from front of fitting. Limited by
Off set Options
property.
|
Rise Left
|
<numeric value>
- Sets the vertical
saddle (End3) offset distance from left (End1) of the tee.
|
Rise Right
|
<numeric value>
- Sets vertical
saddle (End3) offset distance from right (End2) of the tee.
|
Rise Value
|
<numeric value>
- Sets top offset
between End1 and End2.
|
Run
|
<numeric value>
- Sets saddle
(End3) offset distance from left side of fitting. Limited by
Off set Options
property.
|
Run Left
|
<numeric value>
- Sets lateral
saddle (End3) offset distance from left (End2) of the tee.
|
Run Right
|
<numeric value>
- Sets lateral
saddle (End3) offset distance from left (End1) of the tee.
|
Saddle Length
|
<numeric value>
- Sets saddle
length where it meets the main fitting tube.
|
Standard Angle
|
<angle value> between 5° and 90°
- Closest catalog
match for angle property. Set by Manufacturer Catalogs.
|
Straight Left
|
<numeric value>
- Sets the main
branch (at end1) length of tee along bottom side.
|
Straight Left Bottom
|
<numeric value>
- Sets the branch
length of tee at left side down along end3.
|
Straight Left Top
|
<numeric value>
- Sets the main
branch (at end1) length of te along top side.
|
Straight Right
|
<numeric value>
- Sets the branch2
length of tee of along bottom side.
|
Straight Right Bottom
|
<numeric value>
- Sets the branch
length of tee at right side down along end3.
|
Straight Right Top
|
<numeric value>
- Sets the branch
(at end2) length of tee along top side.
|
Offset Options
|
<null value>
- Frees fitting
from any symmetry constraints.
a
<angle value>
- Face is offset by
an angle value.
a<
<angle value>
- Changes the
default minimum angle check of 5° to the New Value.
b
b
<numeric value>
- Bottom is offset
by value.
ba
<angle value>
- Bottom is offset
by an angle.
l
l
<numeric value>
- Left side is
offset by value.
la
<angle value>
- Left side is
offset by an angle.
r
r
<numeric value>
- Right side is
offset by value.
ra
<angle value>
- Right side is
offset by an angle.
s
st
- Symmetric fitting
with respect to top and bottom.
sr
- Symmetric fitting
with respect to left and right.
t
t
<numeric value>
ta
<angle value>
- Top is offset by
an angle.
Combined entries are separated by forward slashes. Entries
are honored in order from left to right. Angle value range is – 85° to + 85°
unless a<xx° is encountered.
|
Offset Options(For Drop
Cheek fittings)
|
<null value>
- Frees top saddle
from any symmetry constraints.
s
- Sets symmetry of
top saddle blend towards main body.
|
Tee Length
|
Positive <numeric value>
- Sets main tube
length between End1 and End2 connect points. Cannot be smaller than Saddle
Length property.
|
Total Length (L)
|
Positive <numeric value>
- Sets overall
length of fitting.
|