Angle
|
<angle value> between 1° and 90°
- Sets actual angle
between outlets based on angle in graphical representation.
|
Auto Size
|
Radius
- RadToDia follows
changes of Radius
RadToDia
- Radius follows
changes of RadToDia.
inradius
- Maintains a
minimum value for outer radius based on inner radius.
r/d=
<numeric value>
- Sets inner and
outer radii based on fitting center line using equation: centerline radius =
depth1 (D1) x <value>
AutoVane
- Calculates vane
size using fitting radii.
- Maintains
proportionality at vane locations.
|
Auto Size
asd-500
|
For Mitre elbow, sets properties to
asd500 catalog specific.
|
Connection 1 | Length (L1)
|
Positive <numeric value>
- Sets the straight
length of connection at End1.
|
Connection 2 | Length (L2)
|
Positive <numeric value>
- Sets the straight
length of connection at End2.
Note: The
L1 and L2 values differ for type of Elbow fittings; for example, for Mitered
Elbows, the default value is 6 inches (imperial) / 150 mm (metric) and the
minimum value should not be less than 2 inches (imperial) / 50 mm (metric).
|
Connection 3 | Length (L3) ... Connection 6 |
Length (L6)
|
<numeric value>
- Set automatically
by application.
|
Connection | End Type
|
fl
-<numeric value>
- Sets and sizes
end with a flange connection.
m
-<numeric value>
- Sets and sizes
end with a male connection.
fe
-<numeric value>
- Sets and sizes
end with a female connection.
Separate End Type entries for each End Spec with a semi
colon.
Example: fl-2;fe-.13 creates a flange at End1
with size 2, and a female connection at End2 with an overall reduction of
component's dimensions of .13
|
Elbow Type
|
0
- No inner and
outer radii.
1
- Radii and custom
vane size.
2
- Radii and vane
extending to outlet.
|
End Segment Angle
|
<angle value> between 1° and 90°
- Sets segment
angle of segments nearest ends for segmented elbows.
|
Front Length
|
Positive <numeric
value>
- Sets length of
the front side of Compound Offset Elbow. It is (L1+D2).
|
Heel Radius
|
Positive <numeric value>
- Sets radius of
heels of elbow.
|
No. of Vanes
|
<zero> and
<integer>
- Sets the number
of vanes.
|
No. Of Mitres
|
<integer> between 2 and 45.
- Sets number of
mitre segments.
Note: Mitre
elbow with
Auto Size asd-500 and Angle <=
30 sets the No. Of Mitres to 1.
|
Number Of Segments
|
<integer>
- Sets number of
segments.
Note: For 0
value, the Oval Angular Elbow behaves as a Normal Elbow and for 2 and above
Segmented Elbow.
|
Offset
|
<numeric value>
- Sets a center
line offset between End1 and End2.
|
Offset Distance (H1)
|
<numeric
value>
(for Compound Offset Elbow)
- Sets the running
offset between elbow ends. It is 6" (150mm) by default, and minimum 2" (50mm).
|
Radius 1 (R1)
|
Positive <numeric value>
|
Radius 2 (R2)
|
Positive <numeric value>
|
Radius
|
Positive <numeric value>
|
Radius to Diameter Ratio
|
<numeric value> greater than or equal to
1
- Sets center
radius by solving equation: centerline radius = depth1 (D1) x <value>
|
Segment Angle
|
<angle value> between 1° and 90°.
- Sets segment
angle. Segments update starting from End1.
|
Side Length
|
Positive <numeric
value>
- Sets length of
the side of Compound Offset Elbow. It is (L2+W1)
|
Standard Angle
|
<angle value> between 5° and 90°
- Closest catalog
match for angle property. Set by Manufacturer Catalogs.
|
Run1 Vane Size
Run3 Vane Size
|
<numeric value>;<numeric
value>
- Sets vane size at
Run#.
- Individual vane
sizes separated by semi colon.
|
Run Side (for
Compound Offset Elbow)
|
1–Front
- Sets the run side
to front.
2–Back
- Sets the elbow run
side to back.
|
Throat Radius
|
Positive <numeric value>
- Sets radius of
throat edges of elbow .
|
Total Height
|
<numeric
value>
- Sets the total
length of the elbow. For Compound Offset Elbow, it is the sum of D1, W2 and
Offset Distance (H1).
|
Vane Length / Radius
|
<numeric value>;<numeric
value>
- Sets vane
characteristics.
- Individual vane
radius or length values are separated by semi colon (semi colons equals to No.
of Vanes).
|
Vane Type
|
0–ShortRadius
- Generates a
curved vane with a radius defined by the Vane Size property.
1–LongRadius
- Generates a
curved vane extending to the elbow's outlets.
2–ShortAngle
- Generates an
angled (no curve) vane.
3–LongAngle
- Generates an
angled vane that extends to the elbow's outlets.
|
Vane Type
|
(for Z and Compound Offset Elbows)
0–ShortRadius
- Generates a
curved vane with a radius defined by the Vane Size property.
1–ShortAngle
- Generates an
angled (no curve) vane.
|