Branch 1 | Angle
|
<angle value> between 5° and 90°
- Sets branch angle
between End1 and End3.
|
Branch 1 | Angle
(for Throat Cross)
|
<angle value> between 30° and 90°
- Sets branch angle
between branch 1 (End3) and End2.
|
Branch 2 | Angle
|
<angle value> between 5° and 90°
- Sets branch angle
between End1 and End4.
|
Branch 2 | Angle
(for Throat Cross)
|
<angle value> between 30° and 90°
- Sets branch angle
between Branch 2 (End4) and End2.
|
Branch 1 | Height
|
Positive <numeric value>
- Sets distance
between main branch center line to the end of End3. Automatically set by
application.
|
Branch 2 | Height
|
Positive <numeric value>
- Sets distance
between main branch center line to the end of End4. Automatically set by
application.
|
Branch1 | Length
|
Positive <numeric value>
- Sets branch
length. Center line distance between side branch divergence point to End3
connect point.
|
Branch2 | Length
|
Positive <numeric value>
- Sets branch
length. Center line distance between side branch divergence point to End4
connect point.
|
Branch 2 | Width
offset Top
|
Positive <numeric value>
- The offset
derived from the Branch 4 Radius and Straight Top.
|
Branch 3 | Radius
(for Drop Cheek fittings )
|
<numeric value> greater than or equal to
zero.
- Sets the inside
radius between End1 and End3.
|
Branch 4 | Radius
|
<numeric value> greater than or equal to
zero.
- Sets the inside
radius between End1 and End4.
|
Branch 3 | Depth
Offset
|
<numeric value>
- Sets center line
distance between End1 connect point and the divergence point of side branch
leading to End3.
|
Branch 4 | Depth
Offset
(for Drop Cheek fittings)
|
<numeric value>
- Sets center line
distance between End1 connect point and the divergence point of side branch
leading to End4.
|
Center To Branch1 Offset
|
<numeric value>
- Sets the distance
between End1 connect point and the divergence point for side branch leading to
End3.
|
Center To Branch2 Offset
|
<numeric value>
- Sets the distance
between End1 connect point and the divergence point for side branch leading to
End4.
|
Branch 1 | Cone Angle
|
<angle value>
- Sets taper angle
as End3 branch blends into the main fitting body of a conical tee.
|
Branch 2 | Cone Angle
|
<angle value>
- Sets taper angle
as End4 branch blends into the main fitting body of a conical tee.
|
Connection 1 | Length (L1)
|
Positive <numeric value>
|
Connection 2 | Length (L2)
|
Positive <numeric value>
- Sets straight
length at End2 for rectangular shapes.
- Sets male
connection length at End2 for round and oval shapes.
|
Connection 3 | Length (L3)
|
Positive <numeric value>
- Sets straight
length at End3 for rectangular shapes.
- Sets male
connection length at End3 for round and oval shapes.
|
Connection 4 | Length (L4)
|
Positive <numeric value>
- Sets straight
length at End4 for rectangular shapes.
- Sets male
connection length at End4 for round and oval shapes.
|
Connection1 | Branch2 Offset
|
<numeric value> greater than or equal to
zero.
- Sets distance
from End1 connect point to End4 (bottom) left side.
|
Connection1 | Branch1 Offset
|
<numeric value> greater than or equal to
zero.
- Sets distance
from End1 connect point to End3 (top) left side.
|
Connection 2 | Branch1 Offset
|
<numeric value> greater than or equal to
zero.
- Sets distance
from End1 connect point to End3 (top) right side.
|
Connection 2 | Branch2 Offset
|
<numeric value> greater than or equal to
zero.
- Sets distance
from End2 connect point to End4 (bottom) right side.
|
Connection | End Type
|
fl
-<numeric value>
- Sets and sizes
end with a flange connection.
m
-<numeric value>
- Sets and sizes
end with a male connection.
fe
-<numeric value>
- Sets and sizes
end with a female connection.
Separate End Type entries for each End Spec with a semi
colon.
Example: fl-2;fe-.13 creates a flange at End1 with
size 2, and a female connection at End2 with an overall reduction of
component's dimensions of .13
For nested fittings, the default is =
-;-;-;-;
|
Inlet to branch1 offset (X11)
|
<numeric value>
- Sets center line
distance between End1 connect point and the divergence point of side branch
leading to End3.
|
Inlet to branch2 offset (X12)
|
<numeric value>
- Sets center line
distance between End1 connect point and the divergence point of side branch
leading to End4.
|
Inset1
|
<numeric value> greater than or equal to
zero.
- Sets distance
from End1 connect point to left side of End3 (saddle). Limited by
System1 Assembly
property.
|
Inset2
|
<numeric value> greater than or equal to
zero.
- Sets distance
from End1 connect point to left side of End4 (saddle). Limited by
System2 Assembly property.
|
Nested Type
|
Radius
|
Radius 1 (R1)
Run1 Radius
|
<numeric value> greater than or equal to
zero.
- Sets the inside
radius between End1 and End3.
|
Radius 2 (R2)
Run3 Radius
|
<numeric value> greater than or equal to
zero.
- Sets the inside
radius between End1 and End4.
|
Radius 2 (R2)
(for Throat Cross)
|
<numeric value> greater than or equal to
zero.
- Sets the inside
radius between End2 and End3.
|
Radius 3 (R3)
(for Throat Cross)
|
<numeric value> greater than or equal to
zero.
- Sets the inside
radius between End1 and End4.
|
Radius 4 (R4)
(for Throat Cross)
|
<numeric value> greater than or equal to
zero.
- Sets the inside
radius between End2 and End4.
|
Reducer Length
|
Positive <numeric value>
- Automatically set
by the application.
|
Rise1
|
<numeric value>
- Sets front offset
between End1 and End3. Front is fully flat with a zero value.
|
Rise2
|
<numeric value>
- Sets front offset
between End1 and End4. Front is fully flat with a zero value.
|
Run1
|
<numeric value>
- Sets left offset
between End1 and End3. Left saddle side is aligned to End1 connect point with a
zero value.
|
Run2
|
<numeric value>
- Sets left offset
between End1 and End4. Left saddle side is aligned to End1 connect point with a
zero value.
|
Run1 Angle
|
<angle value> between 5° and 90°
- Sets branch angle
between End1 and End3.
|
Run1 Number Of Vanes
|
<integer>
- Sets number of
vane blades stacked in the middle of run1 between End1 and End3.
|
Run1 Straight Length
|
<numeric value>
- Sets the straight
length of Run1 at End3.
|
Run1 Throat1 Length
|
<numeric value> greater than 2.
- Sets the length
of throat opening of Run1 at the End1. Minimum 2, default 6, for
nested fittings.
|
Run1 Throat2 Length
|
<numeric value>
- Sets the length
of throat of Run1 branch at the End3. Adds to L3.
Minimum 2, default 6, for nested fittings.
|
Run1 Type
|
Radius
- Sets type of Run1
branch at End3 as Radius.
|
Run1 Vane Size
|
<numeric value>;<numeric
value>
- Sets the size of
vanes stacked in the middle of run1, each value separated with a semi colon for
number of vanes set in Run1NumberOfVanes.
|
Run1 Vane Type
|
0 – ShortRadius
- Angular vane
blades are set at the middle of the run with Short radius.
1 – LongRadius
- Angular vane
blades are set at the middle of the run and extended till both openings (End1
and End3).
2 – ShortAngle
- Short vane blades
are set at the middle of the run in an angle.
3 – Long Angle
- Long vane blades
are set at the middle of the run in an angle, and extended till both openings.
|
Run2 Straight Length
|
<numeric value>
- Sets straight
length between End1 and center of End3.
|
Run3 Angle
|
<angle value> between 5° and 90°
- Sets branch angle
between End1 and End4.
|
Run3 Number Of Vanes
|
<integer>
- Sets number of
vane blades stacked in the middle of run1 between End1 and End4.
Default 0, for nested fittings.
|
Run3 Straight Length
|
<numeric value>
|
Run3 Throat1 Length
|
<numeric value> greater than 2.
- Sets the length
of throat opening of Run3 at the End1. Minimum 2, default 6, for
nested fittings.
|
Run3 Throat2 Length
|
<numeric value>
- Sets the length
of throat of Run3 branch at the End4. Adds to L4.
Minimum 2, default 6, for nested fittings.
|
Run3 Type
|
Radius
- Sets type of Run2
branch at End4 as Radius.
|
Run3 Vane Size
|
<numeric value>;<numeric
value>
- Sets the size of
vanes stacked in the middle of run1, each value separated with a semi colon for
number of vanes set in Run3NumberOfVanes.
|
Run3 Vane Type
|
0 – ShortRadius
- Angular vane
blades are set at the middle of the run with Short radius.
1 – LongRadius
- Angular vane
blades are set at the middle of the run and extended till both openings (End1
and End4).
2 – ShortAngle
3 – Long Angle
- Long vane blades
are set at the middle of the run in an angle, and extended till both openings.
|
Saddle1 Length
|
<numeric value>
- Sets the length
of the bottom saddle where it meets the main fitting body.
|
Saddle2 Length
|
<numeric value>
- Sets the length
of the top saddle where it meets the main fitting body.
|
System1 Assembly
|
<null value>
- Frees bottom
saddle from any symmetry constraints.
s
- Sets symmetry of
bottom saddle blend towards main body.
inset=
<numeric value>:<numeric
value>
- Sets bottom
saddle inset value based on ratio of keyed in values and largest possible value
for inset. Example: For input
<inset=X:Y, solve equation
Inset1=MaxInset*X/(X+Y)
branch=equate
- Applies all
bottom saddle parameters to top saddle.
|
System2 Assembly
Offset Options
|
<null value>
- Frees top saddle
from any symmetry constraints.
s
- Sets symmetry of
top saddle blend towards main body.
inset=
<numeric value>:<numeric
value>
- Sets top saddle
inset value based on ratio of keyed in values and largest possible value for
inset. Example: For input
<inset=X:Y>, solve equation
Inset1=MaxInset*X/(X+Y)
|
Straight Bottom
|
<numeric value>
- Sets the branch
(at end3) length of cross along bottom side.
|
Straight Left Bottom
|
<numeric value>
- Sets the branch
length of tee at left side down along end3.
|
Straight Left Top
|
<numeric value>
- Sets the main
branch (at end1) length of tee of along top side.
|
Straight Right Top
|
<numeric value>
- Sets the branch
(at end2) length of cross along top side.
|
Straight Top
|
<numeric value>
- Sets the branch
(at end4) length of cross along top side.
|
Total Length
|
Positive <numeric value>
- Sets distance
between End1 and End2 connect points.
|
Total Length (L)
|
Positive <numeric value>
- Sets overall
length of fitting.
- Set automatically
by saddle.
|