• Sets side branch angle.

• Sets distance between main branch center line to the end of saddle. Automatically set by application.

• Sets side branch center line length up to connect point. The application limits values to prevent illogical geometry.

• Sets side branch lateral distance from End1.

(for Drop Cheek fittings )

• Sets the inside radius between End1 and End2.

(for Drop Cheek fittings)

• Sets the inside radius between End1 and End3.

(for Drop Cheek fittings)

• Sets center line distance between End1 connect point and the divergence point of side branch leading to End2.

(for Drop Cheek fittings)

• Sets center line distance between End1 connect point and the divergence point of side branch leading to End3.

• Sets distance between main branch center line to the saddle connect point.

• Sets the side branch angle of taper as it blends into the main branch.The application limits values to prevent illogical geometry.

• Sets straight length at End Spec1 for rectangular shapes.
• Sets straight length between End1 and End2 connections for round and oval shapes.

Connection | Length

• Sets straight length at End2 for rectangular shapes.
• Sets connection lengths for round and oval shapes.
• Sets connection lengths for saddle main tube (End1 and End2).

• Sets straight length at End3 for rectangular shapes.
• Sets connection length on saddle (End3).

• Sets inset distance on the right side of saddle.

Length 5 (L5)

• Sets the distance from the main branches' (End1 and End2) center line to the side branch's (End3) connect point.

• Sets and sizes end with a flange connection.

• Sets and sizes end with a male connection.

• Sets and sizes end with a female connection.

Example: fl-2;fe-.13 creates a flange at End1 with size 2, and a female connection at End2 with an overall reduction of component's dimensions of .13

• Sets offset distance between End1 connect point and intersection with the saddle branch.

• Sets the center line distance between End1 connect point and side branch (End3) start point.

• Sets side branch inner radius.

• Sets radius between End1 and End3.

• Sets radius between End2 and End3.

• Automatically set by the application.

• Sets saddle (End3) offset distance from front of fitting. Limited by Off set Options property.

• Sets the vertical saddle (End3) offset distance from left (End1) of the tee.

• Sets vertical saddle (End3) offset distance from right (End2) of the tee.

• Sets top offset between End1 and End2.

• Sets saddle (End3) offset distance from left side of fitting. Limited by Off set Options property.

• Sets lateral saddle (End3) offset distance from left (End2) of the tee.

• Sets lateral saddle (End3) offset distance from left (End1) of the tee.

• Sets saddle length where it meets the main fitting tube.

• Closest catalog match for angle property. Set by Manufacturer Catalogs.

• Sets the main branch (at end1) length of tee along bottom side.

• Sets the branch length of tee at left side down along end3.

• Sets the main branch (at end1) length of te along top side.

• Sets the branch2 length of tee of along bottom side.

• Sets the branch length of tee at right side down along end3.

• Sets the branch (at end2) length of tee along top side.

• Frees fitting from any symmetry constraints.

• Face is offset by an angle value.

• Changes the default minimum angle check of 5° to the New Value.

• Bottom is flat.

• Bottom is offset by value.

• Bottom is offset by an angle.

• Left side is flat.

• Left side is offset by value.

• Left side is offset by an angle.

• Right side is flat.

• Right side is offset by value.

• Right side is offset by an angle.

• Fully symmetric fitting.

• Symmetric fitting with respect to top and bottom.

• Symmetric fitting with respect to left and right.

• Top is flat

• Top is offset by value.

• Top is offset by an angle.

Offset Options(For Drop Cheek fittings)

• Frees top saddle from any symmetry constraints.

• Sets symmetry of top saddle blend towards main body.

• Sets main tube length between End1 and End2 connect points. Cannot be smaller than Saddle Length property.

• Sets overall length of fitting.