| Top Zone
|
The check boxes enable the
Top Zone optional accessories, such as nut
and washers in the top zone (above the anchored surface). The
[…] buttons are used to open database files
where the respective record index is picked from the nut/washer dialog. For
washers between the nuts, the pull-down option can be set to include 1, 2, or
no washers.
|
| Middle Zone
|
The check boxes enable the
Middle Zone optional accessories which are
picked from the bolt database (accessories on the middle zone plate or sleeve
components). The
[…] buttons are used to open bolt database
files where the respective record index is picked from the nut/plate dialog.
|
| Bottom Zone accessories
|
The check boxes enable the
Bottom Zone optional accessories which are
picked from the bolt database (accessories on the bottom zone plate component).
|
| Pl Thk
|
Sets the plate thickness.
|
| Grout Thk
|
Sets the grout thickness.
|
| Anchor bolt diameter
|
(Required) - Sets the anchor bolt diameter. Use
[…] to select a database value for the hook
anchor bolt diameter (recommended).
|
| Select Component
|
Sets the lower zones component type for the anchor
bolt.
- for
Middle Zone
- Plate – Enables
middle zone accessories be set to nuts and plate.
- Sleeve –
Enables middle zone accessory be set to a sleeve.
- None – The
middle zone set a plain bolt segment.
- for
Bottom Zone
- Plate – Enables
bottom zone accessories be set to nuts and plate.
- None – The
bottom zone set a plain bolt segment
Note: For the
Plate component, for both in the Middle
zone and in the Bottom zone, the plate between the nuts provides a pull-down
option for setting plate sharing methods be configured to either Single,
X-Direction, Y-Direction or Complete.
|
| Bolt Styles dimensions
|
The following dimensions are labeled by dimension
lines on the diagram:
- Thread
length - sets the length for anchor bolt treads for Upper / Lower
segment.
- Extrusion
length - sets the anchor bolt extension in Upper zone.
- Embedment
length - sets the anchor bolt depth for Upper / Middle / Lower arm,
less extrusion length.
|
| Name
|
Used to enter/select a name for the anchor bolt
style. Names you enter are saved to the drop down list provided.
Tip: Use
the
 and
 dialog controls to load or save a
style.
|
| Workloose
|
Sets the hole tolerance.
|
| Part list Entry
|
When on, the part is taken in the BOM/partlist.
|
| Material/Grade
|
Sets the material grade taken from the material file.
|
| Item Number
|
A user-defined value for an item number is set here.
|
| Partlist Name
|
Sets the name formatting using naming variables for
BOM/partlists.
|
| Export Name
|
Sets the name formatting using naming variables for
exports/transfers.
|
| Placement Pattern
|
The fields vary depending upon the
Arrange Type is set.
- Arrange
Type – Select the general arrangement method for the pattern,
either
The placement pattern parameters change accordingly.
|
| Rectangular Arrange Type
|
Two sets of values to describe the parametric
patterns along two axis. Both
X Direction and
Y Direction have the same parameters.
Note: To create a
linear pattern, leave the
the
Pattern field for the
Y Direction blank.
|
| Polar Arrange Type
|
A set of values to describe a semi-circular or
circular pattern of anchors.
- Count – Number
of anchor bolts along this direction of the pattern (i.e., number of rows or
columns)
Tip: To create a linear arrangement
of anchors, leave the
Y Direction
Count field blank.
- Radius – Sets
the radius of the Anchor bolt circle.
- Start
angle – Defines the angle at which the first anchor bolt is
created.
-
Included – The angle
subtended between the first and the last anchor bolt created.
- Orientation –
The orientation values in the drop-down list control depend on the arrangement
type selected.
- In – all anchor
bolts are rotated with legs towards the center of the anchor bolt arc
segment or circle
- Out – all
anchor bolts are rotated with legs away from the center of the anchor
bolt arc segment or circle
|
