Angle |
Angles less than or equal to 90°
- Sets the angle between tap pipe End1 and nose End2 of a hose bib.
|
Blade Angle |
Angles less than or equal to 90°
- Sets the rotation (in the plane perpendicular to the valve outlets) of the valve's internal flow obstruction.
|
Blade Depth |
Positive <numeric value>
- Sets the thickness of the valve's internal flow obstruction.
|
Blade Diameter |
Positive <numeric value>
- Sets the diameter of the valve's internal flow obstruction.
The value is limited by the overall diameter of the valve body. |
Body | Depth |
Positive <numeric value>
- Sets depth of valve body.
|
Body | Diameter |
Positive <numeric value>
- Sets cylinder diameter for main body of valve.
|
Body | Length Total Length
|
Positive <numeric value>
- Sets the horizontal length of valve fitting.
- Sets pipe length from End1 connect point to valve center.
|
Body | Outer Diameter |
Positive <numeric value>
- Sets outside diameter for Vent body.
|
Body Type |
- Defines the shape of the upper body of the valve.
|
Body | Width |
Positive <numeric value>
- Sets the width of valve unit.
|
Bypass Height |
Positive <numeric value>
- Sets distance between the bypass center lines at End1 and at End3.
|
Cap Base | Diameter |
Positive <numeric value>
- Sets outside diameter for base of cap on the valve bonnet.
|
Cap Base | Length |
Positive <numeric value>
- Sets length of cap on the valve bonnet.
|
Cap Body | Diameter |
Positive <numeric value>
- Sets diameter of cap placed on the top of valve.
|
Cap Body | Length |
Positive <numeric value>
- Sets length of cap around the pressure adjusting screw on the valve top.
|
Cap Diameter |
Positive <numeric value>
- Sets outside diameter for cap on the body of air vent.
|
Cap | Length |
Positive <numeric value>
- Indicates the preset value for the lengths of the cap, included in Outlet to Top Distance .
|
Cap | Width |
Positive <numeric value>
- Sets the width of the Cap assembly.
|
Cell Library |
<cell library file name>
- Library file name for device cells.
|
Cell Symbol Name |
<cell name>
- Sets the model cell to the device.
Prerequisite of proper Cell Library for AHUs.
|
Center to Connection 1 Distance Inlet to Center Distance
|
Positive <numeric value>
- Sets distance between End1 and valve center.
|
Center to Connection 2 Distance Outlet to Center Distance
|
Positive <numeric value>
- Sets distance between End2 and valve center.
|
Center to Connection 3 Distance |
Positive <numeric value>
- Sets distance between End3 and valve center.
|
Center to Connection 4 Distance |
Positive <numeric value>
- Sets distance between End4 and valve center.
|
Center to Outlet Distance |
Positive <numeric value>
- Sets the length between valve axis to the End2 (outlet).
|
Coil | Diameter |
Positive <numeric value>
- Sets diameters to coil connections (D3–D5) on the branch of valve and cap body.
|
Coil | Length |
Positive <numeric value>
- Sets length of coil connections (D3–D5).
|
Configuration |
-
1-Flow Configuration
-
2-Return Configuration
- Sets DPDC valve configuration to work in flow or return pipework .
|
Connection 1 | Length (L1) Connection 3 | Length (L3)
Connection 3 | Length (L3) Connection 4 | Length (L4)
|
Positive <numeric value>
- Sets the straight length at End1, End2, End3, and End4, respectively
|
Plumbing Connection 1 | Outer Diameter Plumbing Connection 2 | Outer Diameter
Plumbing Connection 3 |Outer Diameter Plumbing Connection 4 |Outer Diameter
|
Positive <numeric value>
- Sets pipe outside diameter for
- End1
- End2
- End3 and
- End4, respectively.
|
Plumbing Connection | Outer Diameter Inlet Outer Diameter
|
Positive <numeric value>
- Sets the outside dimension of the valve main.
- Sets pipe outside diameters for End1. Same for End2, Nose Outer Diameter.
|
Connection | End Type |
fl -<numeric value>
- Sets and sizes end with a flange connection.
m -<numeric value>
- Sets and sizes end with a male connection.
fe -<numeric value>
- Sets and sizes end with a female connection.
Separate End Type entries for each End Spec with a semi colon. Example: fl-2;fe-.13 creates a flange at End1 with size 2, and a female connection at End2 with an overall reduction of component's dimensions of .13
|
Connection | Type |
- 1-SideInlet SideOutlet – Ends side-by-side horizontally opposite.
- 2-SideInlet BottomOutlet – End2 at the base end.
- Determines the positions of the End2 of (Straight Relief) valve.
|
Depth |
Positive <numeric value>
- Sets the width of the valve body/bonnet. Sets depth of switch assembly, in case of flow switch.
|
Diameter Valve Body Diameter
|
Positive <numeric value>
- Sets the diameter of the valve body/bonnet.
|
Diaphragm Depth |
Positive <numeric value>
- Sets the depth of the diaphragm assembly of pressure transducer.
|
Flange Size |
Positive <numeric value>
- Sets the flange dimension, exterior to reducer body at both sides of check valve.
|
Flange | Thickness Motor | Flange Thickness
|
Positive <numeric value>
- Sets the thickness to the flanges attached to both sides of check valve body.
|
Handle Diameter |
Positive <numeric value>
- Sets diameter of handwheel that controls valve operation.
|
Height |
Positive <numeric value>
- Sets vertical distance between the main branch center line and the side branch.
|
Hose | Diameter |
Positive <numeric value>
- Sets hose branch outside diameter for End2.
|
Hose | Length |
Positive <numeric value>
- Sets hose pipe length along main pipe, equal to tangential distance between hose contact and the end of hose pipe at End2.
|
Horizontal Pipe | Length |
Positive <numeric value>
- Sets main pipe length between End2 and End3 connect points. Cannot be smaller than D1 .
|
Horizontal Pipe | Outer Diameter |
Positive <numeric value>
- Sets horizontal pipe outside diameters for End2 and End3. Equal or less than D1.
|
Inlet | Length |
Positive <numeric value>
- Sets the straight length at End1.
|
Inlet to Outlet Distance Connection Height
|
Positive <numeric value>
- AngledRelief - Sets the height between the center of End2 and End1 (inlet).
- PilotRelief/PressureRegulating/StraightRelief - Sets the height between the center of End1 and the base.
|
Length Total Length
|
Positve <numeric value>
- Sets the overall length of the valve body/bonnet including flange thickness, if any.
|
Lever Height |
Positive <numeric value>
- Sets height of the lever attached on the top of branch; equal to distance between End1 center line and the top of the branch.
|
Lever Length Lever Width
|
Positive <numeric value>
- Sets height and width of the lever shaft attached on the top of branch.
|
Nose Length |
Positive <numeric value>
- Sets nose length of branch pipe from End2 connect point.
|
Nose Outer Diameter |
Positive <numeric value>
- Sets nose branch outside diameter for End2. Same as Connection Outer Diameter at End1.
|
Operator Offset |
Positive <numeric value>
- Sets the offset of actuating shaft towards End2.
|
Outlet | Length |
Positive <numeric value>
- Sets the straight length at End2.
|
Outlet to Top Distance |
Positive <numeric value>
- AngledRelief - Sets the height between the center of End2 and the adjusting bolt.
- PilotRelief/PressureRegulating/StraightRelief - Sets height between the center of End1 and the outer surface of the cap of the adjusting bolt.
|
Options |
-
1-Screw
-
2-With Cap
-
3-Pilot
- Defines the option for the top assembly of (pressure regulating) valve.
|
Plate Diameter |
Positive <numeric value>
- Sets outer diameter of cylindrical housing of capacitance plates, used to sense diaphragm positioning and convert the differential pressure into electrical signal.
|
Plate Length |
Positive <numeric value>
- Sets straight length of cylindrical assembly of plates mounted between diaphragm and transmitter of DP Transmitter.
|
Reducer Diameter |
Positive <numeric value>
- Sets diameters of reduce openings of flow/system at both sides of valve.
|
Reducer Length |
Positive <numeric value>
- Sets the distance between the reduce opening and valve body it is attached.
|
Relief Valve Type |
1-Piston Type
- Sets the valve in a cylindrical body structure. It limits a specific pump discharge pressure on machine tool hydraulic systems, oil burning equipment, rams, presses, lifts, etc.
2-Direct Acting
- Sets the type to angle-type suitable to low to moderate flows.
|
Stem Diameter |
Positive <numeric value>
- Sets diameter of branched stem under the cap of differential valve. Follows main diameters at End1/End2.
|
Stem Height
|
Positive <numeric value>
- Sets straight length of branch elevated from center line of End1 main pipe .
|
Stem Offset Branch | Offset
|
Positive <numeric value>
- Sets distance of side branch center from End1 on main pipe.
|
Switch Type |
1-Paddle
- Default type set for flow switch type Paddle valve.
2-Vane
- Default type set for flow switch type Vane valve.
|
Tag |
<alpha-numeric characters>
- Sets tag value visible in output of drawing composition in dynamic view. Separate tag strings with a semi colon
|
Thickness |
Positive <numeric value>
- Sets the valve body's wall thickness.
|
Total Length |
Positive <numeric value>
- Sets the distance between End1 and End2 of valve.
|
Transmitter Diameter |
Positive <numeric value>
- Sets outer diameter of cylindrical housing of transmitter placed on top of valve.
|
Transmitter Length |
Positive <numeric value>
- Sets straight length of transmitter assembly mounted on top of valve.
|
U- Bolt Size |
Positive <numeric value>
- Sets straight distance between two ends of U-bolt.
|
Valve Body Height |
Positive <numeric value>
- Sets the valve unit height from the base.
|
Valve Operator Parameters
|
Name=<type of operator>,A=<numeric value>,B=<numeric value>,C=<numeric value>,Primary=<angle value>,Tertiary=<angle value>,Secondary=<angle value>
- Name:Sets operator type to either Handwheel, Wrench, Electrical or Gear.
- A:-Sets the handwheel's diameter.-Sets the electrical box's larger size dimension. -Sets the vertical offset distance between the valve axis and the wrench. -Sets the vertical offset distance between the valve axis the gear box's centerline.
- B:-Sets the offset distance between the valve and the handwheel. -Sets the offset distance between the valve and the outermost surface of the electrical box. -Sets the horizontal offset distance between the valve axis and the end of wrench.-Sets the distance between the gear box's centerline to the end of the gear actuation shaft.
- C:-Sets the handwheel actuator shaft diameter. -Sets the electrical actuator shaft diameter.-Sets the gear operator hand control diameter.
- D:-Sets the horizontal offset distance between the valve axis and the hand control.
- E:-Sets the horizontal offset distance between the gear actuator shaft and the hand control axis.
- Primary:Sets rotation of operator along the valve axis in degrees.
- Secondary:Sets the orientation of the operator relative to operator's shaft axis.
- Tertiary:Sets rotation of operator perpendicular to the valve axis in degrees. Positive values rotate the operator towards End2 and negative values rotate the operator towards End1.
|
Valve Type |
1-ball
2-globe
- Sets valve type to globe.
3-gate
4-plug
5-other
- Sets valve type to other.
|
Vertical Pipe | Length |
Positive <numeric value>
- Sets vertical pipe length from End1 connect point. Cannot be smaller than Horizontal Pipe Outer Diameter. .
|
Vertical Pipe | Outer Diameter |
Positive <numeric value>
- Sets vertical pipe outside diameter for End1 (D1).
|
Width |
Positive <numeric value>
- Sets width of switch assembly.
|
Wrench Length |
Positive <numeric value>
- Sets length of wrench lever attached on the top of branch used to operate valve.
|